Wikis USB-Boot (en)
[Article: Wiki-eCS-OS/2-USB-Boot-en--Bug-Geo | Diskussion ]
Kingston CF 64 GB and CF 128 MB Card with MBR Record wiped to zero by DFSEE
[Edit]1 CF 64 MB ThinkPad T23 CF-Card in UltraBay with CF-to-IDE Adapter - IBM1S506.ADD
Bild: USB-Boot-CF-64-to-IDE.jpg
driver: IBM1S506.ADD bldlevel 10.161
[Edit]1.1 CF 64 MB Card GEO displayed at boot
Bild: USB-Boot-IBM1S506-add-Output-Screenshot.JPG
values transcribed from JPG:
Controller:1 Port:0170 IRQ:000F Status:OK Bus Master DMA Scatter/Gather PCI Rev:2.1 Intel 82801CA PCI ICH Rev:01 VID:8086 DID:248A
Unit:0 Status:OK LBA PIO0 BIOS Model:TOSHIBA THNCF064MMA 3.00 Drive has valid Enhanced BIOS extensions Version 48 OS2:log phys BIOS:log BPB:log IDE:log phys Total Sectors C 993 978 992 978 978 Avail 125184 H 2 4 2 0 4 4 OS2 125118 S 63 32 63 0 32 32 % Used 99.95
[Edit]1.2 CF 64 MB Card Geo displayed by DFSEE 8-10 ( map -M -m command )
P-Geo Disk 2 Cyl : 978 H: 4 S:63 Bps:512 Size : 0x0001E900 = 61.1 MiB L-Geo Disk 2 Cyl : 993 H: 2 S:63 Bps:512 Size : 0x0001E8BE = 61.1 MiB BIOS Int13 limit : none, no limit MBR crc 8bff08f2 : 0x88bad147 = Bootcode not present. Disk is NOT bootable!
WARNING disk nr 2 : Master boot record is not valid, no partitions recognized
[Edit]2 CF 64 MB ThinkPad T23 CF-Card in UltraBay with CF-to-IDE Adapter - DANIS506.ADD
driver: DANIS506.ADD bldlevel 1.7.7
[Edit]2.1 CF 64 MB Card GEO displayed at boot ( values from IBMS506$ )
Controller:1 Port:0170 IRQ:0F Status:OK Intel ICH3 PATA host (8086:248A rev:01) on PCI 0:31.1 @33MHz
Unit:0 Status:OK LBA PIO0 Identify Model:TOSHIBA THNCF064MMA 3.00 OS2:log phys BPB/BIOS IDE:log phys Total Sectors C 978 978 978 978 Avail 125184 H 4 4 0 4 4 OS2 125184 S 32 32 0 32 32 % Used 100.00
[Edit]2.2 CF 64 MB Card Geo displayed by DFSEE 8-10 ( map -M -m command )
P-Geo Disk 3 Cyl : 0 H: 0 S:0 Bps:512 Size : 0x00000000 = 0.0 KiB L-Geo Disk 3 Cyl : 978 H: 4 S:32 Bps:512 Size : 0x0001E900 = 61.1 MiB BIOS Int13 limit : none, no limit MBR crc 8bff08f2 : 0x88bad147 = Bootcode not present. Disk is NOT bootable!
WARNING disk nr 3 : Master boot record is not valid, no partitions recognized
( Comment: Drive 2 a dummy drive for UltraBay )
[Edit]3 CF 64 MB ThinkPad T23 CF-Card in USB Card Reader - USBMSD.ADD
Bild: USB-Boot-USB-Card-Reader-and-64MB-CF-Card.jpg
driver: USBMSD.ADD 10.162
OS2DASD.DMD 10.104
OS2LVM.DMD 10.105
[Edit]3.1 CF 64 MB Card GEO displayed at boot / insert by drivers
N/A
[Edit]3.2 CF 64 MB Card Geo displayed by DFSEE 8-10 ( map -M -m command )
P-Geo Disk 2 Cyl : 0 H: 0 S:0 Bps:512 Size : 0x00000000 = 0.0 KiB L-Geo Disk 2 Cyl : 61 H: 64 S:32 Bps:512 Size : 0x0001E800 = 61.0 MiB BIOS Int13 limit : none, no limit MBR crc 8bff08f2 : 0x88bad147 = Bootcode not present. Disk is NOT bootable!
WARNING disk nr 2 : Master boot record is not valid, no partitions recognized
Kingston CF 64 GB Card with MBR Record wiped to zero by DFSEE
[Edit]4 CF 64 MB Type "extra ME" Thin Client 8364-S20 - DANIS506.ADD
driver: DANIS506.ADD bldlevel 1.7.10
[Edit]4.1 CF 64 MB Type "extra ME" Card GEO displayed at boot ( values from IBMS506$ )
R1.7.10 /W
Daniela's Bus Master IDE Driver for OS/2 Version 1.7.10
Controller:0 Port:01F0 IRQ:0E Status:OK
Intel PIIX4 PATA host (8086:7111 rev:01) on PCI 0:5.1 @33MHz
Unit:0 Status:OK LBA PIO0 BPB
Model:Flash Card 02/02/05
OS2:log phys BPB/BIOS IDE:log phys Total Sectors
C 62 500 500 500 Avail 128000
H 64 8 64 8 8 OS2 126976
S 32 32 32 32 32 % Used 99.19
Comments:
64 MB CF Card Type "extra ME" size is 1 MB more compared to 64 MB Card Type "Kingston"
Different P-GEO and L-GEO - Status: Card is not wipe, MBR written by IBM1S506, USBMSD?
Why are OS2-log and BPB and IDE-phys not all eQual? any sense?
[Edit]5 CF 128 MB ThinkPad T23 CF-Card in UltraBay with CF-to-IDE Adapter - IBM1S506.ADD
Bild: USB-Boot-CF-128-to-IDE.jpg
driver: IBM1S506.ADD bldlevel 10.161
[Edit]5.1 CF 128 MB Card GEO displayed at boot
Bild: USB-Boot-CF-128-IBM1S506-add-Output-Screenshot.JPG
values transcribed from JPG:
Controller:1 Port:0170 IRQ:000F Status:OK PCI Rev: 2.10 Intel 82801CA PCI ICH Rev:01 VID:8086 DID:248A
Unit:0 Status:OK POI8 PBP Model:Hitachi XXM2.3.0 3.00 Drive has valid Enhanced BIOS extensions Version 48 OS2:log phys BIOS:log BPB:log IDE:log phys Total Sectors C 122 978 992 978 978 Avail 250368 H 64 8 4 64 8 8 OS2 249856 S 32 32 63 32 32 32 % Used 99.80
[Edit]5.2 CF 128 MB Card Geo displayed by DFSEE 8-10 ( map -M -m command )
[Edit]6 CF 128 MB ThinkPad T23 CF-Card in UltraBay with CF-to-IDE Adapter - DANIS506.ADD
[Edit]6.1 Driver: DANIS506.ADD bldlevel 1.7.7
[Edit]6.1.1 CF 128 MB Card GEO displayed at boot ( values from IBMS506$ R 1.7.7)
Controller:1 Port:0170 IRQ:0F Status:OK Intel ICH3 PATA host (8086:248A rev:01) on PCI 0:31.1 @33MHz
Unit:0 Status:OK LBA PIO0 BPB Model:Hitachi XXM2.3.0 Rev 3.00 OS2:log phys BPB/BIOS IDE:log phys Total Sectors C 122 978 978 978 Avail 250368 H 64 8 64 8 8 OS2 249856 S 32 32 32 32 32 % Used 99.79
[Edit]6.1.2 CF 128 MB Card Geo displayed by DFSEE 8-11 Beta( map -M -m command )
P-Geo Disk 2 Cyl : 978 H: 8 S:63 Bps:512 Size : 0x0003D200 = 122.3 MiB L-Geo Disk 2 Cyl : 122 H: 64 S:32 Bps:512 Size : 0x0003D000 = 122.0 MiB BIOS Int13 limit : none, no limit MBR crc c51e1623 : 0x7ea9d168 = IBM OS/2 LVM, 14.105 May 2006, I13X
Comment: MBR present --> CF Card has been partitioned
[Edit]6.2 Driver: DANIS506.ADD bldlevel 1.7.8
[Edit]6.2.1 CF 128 MB Card GEO displayed at boot ( values from IBMS506$ R 1.7.8)
R1.7.8 /W Daniela's Bus Master IDE Driver for OS/2 Version 1.7.8 Controller:0 Port:01F0 IRQ:0E Status:OK BusMaster Scatter/Gather Intel ICH3 PATA host (8086:248A rev:01) on PCI 0:31.1 @33MHz Unit:0 Status:OK SMS:16 LBA NL:126 BusMaster UltraDMA5/PIO4 BPB Model:Hitachi HTS541616J9AT00 SB4OA70H OS2:log phys BPB/BIOS IDE:log phys Total Sectors C 20673 65535 65535 16383 Avail 312581808 H 240 16 240 16 16 OS2 312575760 S 63 63 63 63 63 % Used 99.99 Controller:1 Port:0170 IRQ:0F Status:OK Intel ICH3 PATA host (8086:248A rev:01) on PCI 0:31.1 @33MHz
Unit:0 Status:OK LBA PIO0 BPB Model:Hitachi XXM2.3.0 Rev 3.00 OS2:log phys BPB/BIOS IDE:log phys Total Sectors C 122 978 978 978 Avail 250368 H 64 8 64 8 8 OS2 249856 S 32 32 32 32 32 % Used 99.79
[Edit]6.2.2 CF 128 MB Card Geo displayed by DFSEE 8-11 Beta ( map -M -m command )
P-Geo Disk 1 Cyl : 16383 H: 16 S:63 Bps:512 Size : 0x0FFFFFFF = 131071 MiB L-Geo Disk 1 Cyl : 20673 H:240 S:63 Bps:512 Size : 0x12A18710 = 152624 MiB BIOS Int13 limit : 1024 cylinders, limiting to Size : 7560.0 MiB MBR crc c51e1623 : 0x7ea9d168 = IBM OS/2 LVM, 14.105 May 2006, I13X
P-Geo Disk 2 Cyl : 978 H: 8 S:63 Bps:512 Size : 0x0003D200 = 122.3 MiB L-Geo Disk 2 Cyl : 512 H: 12 S:32 Bps:512 Size : 0x00030000 = 96.0 MiB Error, disk 2 PD2 : reading the MBR info in the 1st sector failed! DUMMY, disk 2 seems reserved with no media present (USB/PCCARD etc)
P-Geo Disk 3 Cyl : 0 H: 0 S:0 Bps:512 Size : 0x00000000 = 0.0 KiB L-Geo Disk 3 Cyl : 122 H: 64 S:32 Bps:512 Size : 0x0003D000 = 122.0 MiB BIOS Int13 limit : none, no limit MBR crc c51e1623 : 0x7ea9d168 = IBM OS/2 LVM, 14.105 May 2006, I13X
Comment: MBR present --> CF Card has been partitioned
snippet of config.sys ( mini system boot to command prompt )
BASEDEV=usbmsd.add /V /FLOPPIES:0 /REMOVABLES:1 /CDS:0 /REMOVEABLE_AS_FLOPPY . . BASEDEV=ibm1flpy.add /A:0 /FORCE:2 /U:0 /F:1.44MB /U:1 /F:1.44MB . rem BASEDEV=IBM1S506.add /W rem BASEDEV=IBMIDECD.flt . BASEDEV=danis506.add /W rem BASEDEV=daniatap.flt /W /A:1 /U:0 /TYPE:W . . BASEDEV=os2dasd.dmd BASEDEV=os2lvm.dmd
Output of Danis DiskInfo I ( from R 1.7.9 package)
0/m: Hitachi HTS541616J9AT00 SB4OA70H SB0400SJG0HW1A ATA device, with non-removable media
Model Number: Hitachi HTS541616J9AT00
Serial Number: SB0400SJG0HW1A
Firmware Revision: SB4OA70H
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 312581808 device size with Mi= 1024*1024: 152628 MiBytes device size with M = 1000*1000: 160042 MBytes (160 GB) Capabilities: LBA, IORDY(can be disabled) Buffer type: 0003: dual port, multi-sector with read caching ability Buffer size: 7512.0kB Queue depth: 1 Standby timer values: spec'd by Vendor, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 128 (0x80 Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=240ns IORDY flow control=120ns Commands/features: Enabled Supported: * NOP cmd * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set - Security Mode feature set * SMART feature set * FLUSH CACHE EXT command * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * 48-bit Address feature set - Automatic Acoustic Management feature set - SET MAX security extension - Address Offset Reserved Area Boot * SET FEATURES subcommand required to spinup after power up - Power-Up In Standby feature set * Advanced Power Management feature set * DOWNLOAD MICROCODE cmd * General Purpose Logging feature set * SMART self-test * SMART error logging Security: Master password revision code = 65534 * supported not enabled not locked * frozen
not expired: security count not supported: enhanced erase 82min for SECURITY ERASE UNIT. HW reset results: CBLID- above Vih Device num = 0 determined by the jumper Checksum: correct
0/s: (not present)
1/m: Hitachi XXM2.3.0 Rev 3.00 X0312 20030915102722
CompactFlash ATA device, with removable media Model Number: Hitachi XXM2.3.0 Serial Number: X0312 20030915102722 Firmware Revision: Rev 3.00 Standards: Likely used: 4 Configuration: Logical max current cylinders 978 978 heads 8 8 sectors/track 32 32 -- bytes/track: 0 bytes/sector: 512 CHS current addressable sectors: 250368 LBA user addressable sectors: 250368 device size with Mi= 1024*1024: 122 MiBytes device size with M = 1000*1000: 128 MBytes Capabilities: LBA, IORDY(may be)(cannot be disabled) Buffer type: 0002: dual port, multi-sector Buffer size: 1.0kB bytes avail on r/w long: 4 Queue depth: 1 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 1 Current = 0 DMA: not supported PIO: pio0 pio1
1/s: (not present)
[Edit]7 CF 128 MB ThinkPad T23 CF-Card in USB Card Reader - USBMSD.ADD
xttp://os4you.org/fileadmin/wikis/usb-boot/USB-Boot-USB-Card-Reader-and-128MB-CF-Card.png
Bild: USB-Boot-USB-Card-Reader-and-128MB-CF-Card.jpg
driver: USBMSD.ADD 10.162
OS2DASD.DMD 10.104
OS2LVM.DMD 10.105
[Edit]7.1 CF 128 MB Card GEO displayed at boot / insert by drivers
N/A
[Edit]7.2 CF 128 MB Card Geo displayed by DFSEE 8-11 ( map -M -m command )
testcase to do!!
[Edit]8 CF 1 GB ThinkPad T23 CF-Card in UltraBay with CF-to-IDE Adapter - DANIS506.ADD
[Edit]8.1 CF 1 GB Card from A-DATA
Bild: USB-Boot-CF-128-to-IDE-A-DATA.jpg
[Edit]8.1.1 Driver: DANIS506.ADD bldlevel 1.7.9
New 1 GB CF Card out of the box without the wipping of the boot sector
[Edit]8.1.1.1 CF 1 GB MB Card (product: A-DATA) GEO displayed at boot ( values from IBMS506$ R 1.7.9)
R1.7.9 /W Daniela's Bus Master IDE Driver for OS/2 Version 1.7.9 Controller:0 Port:01F0 IRQ:0E Status:OK BusMaster Scatter/Gather Intel ICH3 PATA host (8086:248A rev:01) on PCI 0:31.1 @33MHz Unit:0 Status:OK SMS:16 LBA NL:126 BusMaster UltraDMA5/PIO4 BPB Model:Hitachi HTS541616J9AT00 SB4OA70H OS2:log phys BPB/BIOS IDE:log phys Total Sectors C 20673 65535 65535 16383 Avail 312581808 H 240 16 240 16 16 OS2 312575760 S 63 63 63 63 63 % Used 99.99 Controller:1 Port:0170 IRQ:0F Status:OK BusMaster Scatter/Gather Intel ICH3 PATA host (8086:248A rev:01) on PCI 0:31.1 @33MHz Unit:0 Status:OK LBA BusMaster MWordDMA2/PIO4 BIOS Model:CF 1GB 20060911 OS2:log phys BPB/BIOS IDE:log phys Total Sectors C 1007 2014 1007 2014 Avail 2030112 H 32 16 32 32 16 OS2 2030112 S 63 63 63 63 63 % Used 100.00
[Edit]8.1.1.2 CF 1 GB Card (product: A-DATA) Geo displayed by DFSEE 8-11 Beta ( map -M -m command )
Number of disks : 3
P-Geo Disk 1 Cyl : 16383 H: 16 S:63 Bps:512 Size : 0x0FFFFFFF = 131071 MiB L-Geo Disk 1 Cyl : 20673 H:240 S:63 Bps:512 Size : 0x12A18710 = 152624 MiB BIOS Int13 limit : 1024 cylinders, limiting to Size : 7560.0 MiB MBR crc c51e1623 : 0x7ea9d168 = IBM OS/2 LVM, 14.105 May 2006, I13X
P-Geo Disk 2 Cyl : 2014 H: 16 S:63 Bps:512 Size : 0x001EFA20 = 991.3 MiB L-Geo Disk 2 Cyl : 2014 H: 16 S:63 Bps:512 Size : 0x001EFA20 = 991.3 MiB BIOS Int13 limit : 1024 cylinders, limiting to Size : 504.0 MiB MBR crc 2f7d8cc7 : 0xaa3df0e4 = MBR bootcode unknown to DFSee
P-Geo Disk 3 Cyl : 0 H: 0 S:0 Bps:512 Size : 0x00000000 = 0.0 KiB L-Geo Disk 3 Cyl : 512 H: 12 S:32 Bps:512 Size : 0x00030000 = 96.0 MiB Error, disk 3 PD3 : reading the MBR info in the 1st sector failed! DUMMY, disk 3 seems reserved with no media present (USB/PCCARD etc)
Wipe the MBR with DFSee and shutdown, power off - on, restart
DFSee 8-11 Beta 20007-02-15 shows the same values for L-GEO as in output of DANIS506
Number of disks : 3
P-Geo Disk 1 Cyl : 16383 H: 16 S:63 Bps:512 Size : 0x0FFFFFFF = 131071 MiB L-Geo Disk 1 Cyl : 20673 H:240 S:63 Bps:512 Size : 0x12A18710 = 152624 MiB BIOS Int13 limit : 1024, I13X support needed beyond : 7560.0 MiB MBR crc c51e1623 : 0x7ea9d168 = IBM OS/2 LVM, 14.105 May 2006, I13X
P-Geo Disk 2 Cyl : 2014 H: 16 S:63 Bps:512 Size : 0x001EFA20 = 991.3 MiB L-Geo Disk 2 Cyl : 1007 H: 32 S:63 Bps:512 Size : 0x001EFA20 = 991.3 MiB BIOS Int13 limit : none, no limit for this disk MBR crc 8bff08f2 : 0x88bad147 = Bootcode not present. Disk is NOT bootable!
WARNING disk nr 2 : Master boot record is not valid, no partitions recognized P-Geo Disk 3 Cyl : 0 H: 0 S:0 Bps:512 Size : 0x00000000 = 0.0 KiB L-Geo Disk 3 Cyl : 512 H: 12 S:32 Bps:512 Size : 0x00030000 = 96.0 MiB Error, disk 3 PD3 : reading the MBR info in the 1st sector failed! DUMMY, disk 3 seems reserved with no media present (USB/PCCARD etc)
[Edit]8.1.2 CF 1 GB MB ThinkPad T23 CF-Card in USB Card Reader - USBMSD.ADD
Bild: USB-Boot-USB-Card-Reader-and-1GB-CF-Card.jpg
driver: USBMSD.ADD 10.162
OS2DASD.DMD 10.104
OS2LVM.DMD 10.105
[Edit]8.1.3 CF 1 GB MB Card GEO displayed at boot / insert by drivers
N/A
[Edit]8.1.4 CF 1 GB MB Card Geo displayed by DFSEE 8-11 ( map -M -m command )
testcase to do!!
[Edit]8.2 CF 1 GB Card from A-DANE-ELEC
Bild: USB-Boot-1-GB-to-IDE-DANE-ELEC.jpg
[Edit]8.2.1 Driver: DANIS506.ADD bldlevel 1.7.9
New 1 GB CF Card out of the box without the wipping of the boot sector
[Edit]8.2.1.1 CF 1 GB MB Card (product: DANE-ELEC) GEO displayed at boot ( values from IBMS506$ R 1.7.9)
R1.7.9 /W Daniela's Bus Master IDE Driver for OS/2 Version 1.7.9 Controller:0 Port:01F0 IRQ:0E Status:OK BusMaster Scatter/Gather Intel ICH3 PATA host (8086:248A rev:01) on PCI 0:31.1 @33MHz Unit:0 Status:OK SMS:16 LBA NL:126 BusMaster UltraDMA5/PIO4 BPB Model:Hitachi HTS541616J9AT00 SB4OA70H OS2:log phys BPB/BIOS IDE:log phys Total Sectors C 20673 65535 65535 16383 Avail 312581808 H 240 16 240 16 16 OS2 312575760 S 63 63 63 63 63 % Used 99.99
Controller:1 Port:0170 IRQ:0F Status:OK Intel ICH3 PATA host (8086:248A rev:01) on PCI 0:31.1 @33MHz Unit:0 Status:OK LBA PIO4 BPB Model:TOSHIBA THNCF1G02QG 3.00 OS2:log phys BPB/BIOS IDE:log phys Total Sectors C 992 1985 992 1985 Avail 2000880 H 32 16 32 32 16 OS2 1999872 S 63 63 63 63 63 % Used 99.94
[Edit]8.2.2 CF 1 GB (product: DANE-ELEC) MB ThinkPad T23 CF-Card in USB Card Reader - USBMSD.ADD
Bild: USB-Boot-USB-Card-Reader-and-1GB-CF-Card-DANE-ELEC.jpg
driver: USBMSD.ADD 10.162
OS2DASD.DMD 10.104
OS2LVM.DMD 10.105
[Edit]8.2.2.1 CF 1 GB MB Card (product: DANE-ELEC)GEO displayed at boot / insert by drivers
N/A
[Edit]8.2.2.2 CF 1 GB Card (product: DANE-ELEC) Geo displayed by DFSEE 8-11 Beta ( map -M -m command )
Number of disks : 3
P-Geo Disk 1 Cyl : 16383 H: 16 S:63 Bps:512 Size : 0x0FFFFFFF = 131071 MiB L-Geo Disk 1 Cyl : 20673 H:240 S:63 Bps:512 Size : 0x12A18710 = 152624 MiB BIOS Int13 limit : 1024 cylinders, limiting to Size : 7560.0 MiB MBR crc c51e1623 : 0x7ea9d168 = IBM OS/2 LVM, 14.105 May 2006, I13X
P-Geo Disk 2 Cyl : 1985 H: 16 S:63 Bps:512 Size : 0x001E87F0 = 977.0 MiB L-Geo Disk 2 Cyl : 512 H: 12 S:32 Bps:512 Size : 0x00030000 = 96.0 MiB Error, disk 2 PD2 : reading the MBR info in the 1st sector failed! DUMMY, disk 2 seems reserved with no media present (USB/PCCARD etc)
P-Geo Disk 3 Cyl : 0 H: 0 S:0 Bps:512 Size : 0x00000000 = 0.0 KiB L-Geo Disk 3 Cyl : 1984 H: 16 S:63 Bps:512 Size : 0x001E8400 = 976.5 MiB BIOS Int13 limit : 1024 cylinders, limiting to Size : 504.0 MiB MBR crc 65f4cd2f : 0x01f61820 = VirtualPC or classic DOS
[Edit]9 Conclusion:
CF 64 MB
1 Point 1.2 Dfsee Value Phy S 64 does not look okay, should be 32 2 Point 1.1 OS2 Phy values does not look okay?
3 Point 2.1 and 3.2 Bios log values missing
4 3 diffenrent OS/2 logical GEO s
IBM1S506 DANIS506 USBMSD
C 993 978 61
H 2 4 64
S 63 32 32
CF 128 MB
Last changed: 08.08.2007 23:26 by 62.143.44.80 -
Druckansicht Startseite
Wikis USB-Boot (en) Vereinstermine
plugin.tt_news ERROR:No singlePid defined
No HTML template found
--> Did you include the static TypoScript template ('News settings') for tt_news?
